D60 Dearomatized Solvent · European B2B Sourcing
D60 is typically evaluated when buyers need a balanced low-odour dearomatized hydrocarbon, flash point typically ~65°C, aromatics ≤0.001 wt%, distillation 185–214°C. The key questions are not just technical: is the grade available, does the specification support approval, and is the supply route workable for your destination and volume.
Availability, pricing and grade positioning can shift quickly depending on refinery output, seasonal demand and market conditions. Early enquiries are easier to support than last-minute requirements.
Used by purchasing managers, formulators and distributors who need a fast commercial answer before moving into approval or reformulation.
Comparing adjacent grades? See the D-cuts selection guide, review D40 if faster drying matters, or D80 if you need a heavier, slower-evaporating profile.
Fast commercial starting point
What you typically want from a D60 enquiry
A good first response should immediately tell you whether the requirement is workable, what the real market position is, and whether the grade can actually be supplied under current conditions.
Flash point
~65°C typical
Commercial minimum ~62°C sales spec.
Aromatics
≤0.001 wt% typical
Sales spec max 0.10 wt%.
Distillation
185–214°C typical
IBP to dry point (indicative).
Density at 15°C
~793 kg/m³ typical
Sales spec 774–809 kg/m³.
Supply formats
Bulk · IBC · Drums
Subject to route and volume review.
Grade selection
D60 sits in the middle of the dearomatized D-cut family. Buyers usually look at it when they want a low-aromatic hydrocarbon with a flash point above ~60°C, without moving to the slower, heavier end of the range.
In practice, most wrong solvent selections start from the grade name instead of the operational constraint, validating this early typically avoids requalification delays, internal rejection or unnecessary formulation work.
Choose D60 when
You need a balanced dearomatized solvent for cleaners, coatings or industrial formulations where both flash-point comfort and practical drying behaviour matter. D60 is typically selected when neither the lightest nor the heaviest grade in the family is the right answer.
Consider D40 instead
If the process really needs faster evaporation, lower viscosity behaviour or a lighter flash-point profile, D40 or another lighter cut is likely closer to the target. D60 may dry too slowly for applications where evaporation rate is a hard constraint. See how D60 compares to faster D40 grades.
Consider D80 instead
When the application prioritises lower volatility, slower evaporation or a higher flash point than D60 typically offers, D80 or above is usually the more appropriate direction.
Always verify
Final fit depends on the actual current sales specification, formulation requirements, compliance obligations and packaging route. D60 should not be approved on the grade name alone.
Technical specification
A usable technical starting point. The typical column reflects supplied product documentation. The sales-spec column is what governs the actual transaction. They are not the same and should not be treated as interchangeable.
All values are indicative and prefixed with ~ to reflect their indicative nature. Actual figures depend on the specific supply route and must be confirmed at quotation stage. Two D60 offers with the same grade name can differ materially in distillation curve, density and documentation. Approval should always be based on the specific batch documentation. SDS, TDS and CoA available on request prior to supply.
Grade context
A practical buying comparison, not a producer spec table. The purpose is to help frame whether D60 is worth reviewing for the requirement, or whether a lighter or heavier grade is commercially more logical.
| Decision point | D40 | D60 | D80 |
|---|---|---|---|
| Typical buying logic | Lighter and quickerUsually reviewed where faster evaporation matters more than flash-point comfort. | Balanced middle groundOften chosen when buyers want low aromatics plus a comfortable handling profile without moving to the heavy end. | Heavier and slowerMore relevant when lower volatility and slower drying are part of the application requirement. |
| Flash-point direction | Lower than D60. | Typically around or above ~62°C. | Higher than D60. |
| Evaporation direction | Faster than D60. | Mid-range within the family. | Slower than D60. |
| Typical buyer question | "Will D60 dry too slowly for this process?" | "Can we get the right balance between handling comfort and solvent performance?" | "Do we actually need to go this heavy for what we are formulating?" |
For a broader grade-selection guide, see Which D-cut grade?
Applications
The actual grade decision depends on formulation requirements and compliance obligations, but these are the sectors and discussions where D60 most consistently comes up. Application suitability is the buyer's responsibility to verify.
Cleaners
Industrial cleaning and degreasing
Maintenance cleaners, degreasing systems and process-cleaning products where buyers want low aromatics and a practical flash-point profile above ~60°C. Also compare with isopropyl alcohol (IPA) where polar solvency is part of the technical target.
Coatings
Protective and decorative formulations
Reviewed for coatings, primers, maintenance paints and related systems where a controlled hydrocarbon carrier is needed without moving into aromatic-rich material. Adjacent reading: SBP cuts guide.
Metalworking
Metalworking and workshop products
Relevant for formulations where odour profile, solvent behaviour and practical site-handling characteristics all matter during production or field use, particularly where compliance pressure around aromatics is present.
Industrial blending
General industrial formulation work
Considered by chemical distributors and formulators looking for a mid-range low-aromatic hydrocarbon solvent with a consistent, well-documented specification for repeat supply requirements.
Buying checklist
These are the items that usually determine whether a D60 discussion moves forward quickly or stalls at the first internal review.
Most incorrect solvent selections come from starting with the grade name instead of the process constraint, validating this early typically avoids requalification delays, internal rejection or unnecessary formulation work.
Is D60 really the correct grade?
Buyers often start with the name they know, then realise the actual need is lighter or heavier once flash point and drying behaviour are discussed. Confirming this early prevents internal specification rework later.
Does the current sales specification fit the application?
Approval should be based on the current route documentation, not on generic memory of the grade. Different supply routes can produce meaningfully different specifications within the same grade band.
Which packaging format makes sense?
Bulk, IBC and drums each change economics, lead time and site practicality. The right answer depends on volume, unloading capability and frequency of requirement, not just unit price.
Is the destination commercially realistic?
Feasibility depends on delivery country, timing, volume and route position at the time of enquiry. Not every destination is equally accessible from every supply position at every moment.
Is supply actually available for your timing?
In volatile markets, availability can change weekly depending on refinery output, allocations and vessel arrivals. Early enquiry improves the chances of workable supply.
Useful adjacent reading
Compare family logic in the dearomatized D-cuts guide for a full picture of the D30–D120 range and how to choose between grades.
Check isoparaffinic solvents if a different hydrocarbon profile with stricter aromatic control may fit the application better.
Review flash point vs boiling range if the distinction between these two parameters is relevant to your internal approval or safety classification process.
Supply logic
The most useful quotation discussions are the ones where packaging format is aligned with actual usage, delivery geography and unloading reality.
Bulk tanker
Usually the most economical route for larger industrial demand and recurring consumption. Best when the site is equipped for unloading and the requirement is commercially large enough to justify tanker logistics.
IBC supply
Makes sense for mid-range volumes, qualification work, multi-site demand or buyers who want flexibility without immediately committing to full bulk handling.
Drums
Relevant for smaller volumes, more fragmented demand or sites where access, storage or handling rules make drums more practical than IBC or tanker supply.
Also relevant
If D60 is not the right fit for the application, these are the pages most commonly reviewed alongside it.
FAQ
What is D60 usually used for?
Most D60 enquiries relate to industrial cleaners, coatings, maintenance products, metalworking-related blends and other industrial formulations where a low-aromatic hydrocarbon with a mid-range profile is being considered.
Is D60 the same from every supplier?
No. D60 refers to a recognizable grade band, but exact aromatic content, density, distillation behaviour and documentation can vary by source and supply route. Always review the current sales specification for the material actually being quoted.
Can D60 be supplied in bulk, IBC and drums?
Yes, depending on volume, route and current supply position. Bulk is usually the most practical for larger volumes. IBC and drum options can be discussed when the route and packaging position support them.
Do you provide SDS and current sales specification?
Yes. Current sales specification and SDS can be shared during the quotation process, subject to the actual supply route and available producer documentation.
How should D60 be compared with D40 or D80?
At a commercial level, D40 is usually reviewed when faster drying matters more, D80 when lower volatility and a higher flash point matter more, and D60 when buyers want a middle ground between those two directions.
Is D60 classified as dangerous goods for transport?
According to the supplied SDS, D60 is not regulated for ADR, IMDG or IATA in normal packaged transport, but is regulated when transported in tank vessels. Buyers should always review the current SDS for the exact route and transport mode being discussed.
Is D60 always available in Europe?
No. Availability depends on refinery output, seasonal demand and allocation. In tighter markets, D60 can become limited or shift significantly in price week-to-week. Buyers typically validate availability early rather than assuming continuity.
What is the price of D60 in Europe?
D60 pricing depends on refinery output, availability, volume, delivery location and packaging format. Prices can move weekly. Most buyers request a current quotation rather than relying on historic price levels.
Commercial enquiries
A complete enquiry allows a commercially realistic answer from the relevant supplier in the network, including whether the grade is available, how it is currently priced, and whether the requirement is actually workable under current market conditions.
No obligation enquiry, used by buyers to validate price, availability and technical fit before committing internally.
Industrial B2B enquiries only, typical volumes start from ~5 MT and above.
If you are comparing D60 with D40, D80 or another grade, it is usually more efficient to validate pricing and availability early before investing further in technical approval.
All offers are subject to availability and subject to final confirmation. Specification, packaging format, availability, timing and pricing are confirmed at quotation stage based on the current supply route. Final suitability and regulatory compliance remain the responsibility of the buyer.
Enquiry received.
A commercial response will follow from the relevant supplier in the network.
Submission could not be completed.
Please try again, or email us at enquiries@alcoris.eu.
Prefer to contact directly?
Commercial Enquiries
enquiries@alcoris.euMobile
+32 (0)484 94 51 52Enquiries are reviewed and forwarded to the relevant supplier in the network for direct response. If the requirement falls outside current sourcing capability, we will say so directly rather than leave the enquiry without a clear answer.